| CELOS - ERGOline Touch |
CELOS - ERGOline Touch to facilitate
machine operation incl. 21.5 ERGOline Touch ® control with multi
touch screens Uniform management, documentation and visualization of
order, process - and machine data Networkable with CAD / CAM User
friendly and p |
| (Left Spindle) Hollow Cylinder set for
KITAGAWA 24in. Hollow Chuck B-24A1521D (without chuck body)
(SK-OP) |
(Left Spindle) Hollow Cylinder Set for 24-inch)
Chuck B-24A1521D (Bar work capacity dia. 117 mm (4.61 inch)) Hollow
cylinder and draw bar are included as a set. Chuck is not included.
Please see the chuck-cylinder combination diagram for the
combination |
| (Left Spindle) KITAGAWA 24in. Hollow
Chuck B-24A1521D (SK-OP) |
(Left Spindle) KITAGAWA 24-inch Hollow Chuck
B-24A1521D Three-jaw hydraulic chuck manufactured by Kitagawa Iron
Works. Chuck outer diameter: Ø610 mm (dia.24.02 inch.) Through-hole
diameter: Ø165 mm (dia.6.5 inch.) Gripping diameter: Max. Ø610 mm
(dia.2 |
| Chuck foot switch (double) for spindle
1 |
Chuck foot switch (double) for spindle 1 You can
open/close the chuck with two foot switches. |
| Turret : Y-axis |
Turret: Y-axis It moves the turret in the Y-axis
direction. In combination with the rotary tool spindle and spindle 2,
it implements process integration for workpieces with complicated
shapes. Please refer to the turret interference diagrams for the
mova |
| Rotary tool spindle 117/62.3 Nm, |
Rotary Tool Spindle 117/62.3 Nm (86.29/45.95
ft·lbf), 4,000 min-1 Standard rotary tool spindle for the 12-station
in-house bolt-tightened turret specification. BMT (Built-In Motor
Turret) is installed with the milling specification, and the oil
jacket |
| 12-station bolt-tightened turret
(standard specification) (Y, SY, SMC) |
12-Station Bolt-Tightened Turret (Standard
Specification) (Y, SY, SMC) In-house 12 station turret. Please refer
to the axis travel diagrams and turret interference diagrams for the
movable region. Number of tool stations: 12 Shank height for square
too |
| Tailstock spindle built-in center MT5
(Standard) |
Tailstock Spindle Built-in Center MT5 (Standard
Specifications) The built-in center specification is suitable for
heavy cutting. The built-in center can be shaped into various forms
and is relatively inexpensive. Taper hole of tailstock spindle: MT5
(bui |
| Foot switch for tailstock (SK-OP) |
Foot Switch for Tailstock The tailstock is
advanced or retracted using two foot switches. |
| Chip conveyor (right discharge, hinge
type) (/2000) |
Chip Conveyor (Right Discharge, Hinge Type)
(/2000) Chips are conveyed on the hinged plates and discharged to the
right side of the machine. The hinged plate is effective in
discharging long chips. Not suitable for discharging minute powdery
chips gener |
|
|
| Mist collector (AFS 1600), including
stand |
Mist Collector (AFS 1600), Including Stand The
mist collector collects dust and particles and condenses oil mist and
smoke generated during the machining process. The filtered mist is
returned back to the coolant tank. This option includes stand to
moun |
| (Spindle 1) Automatic in-machine tool
presetter (pivoting type, without Air blow for presetter, need to
clean manually before measuring) (Standard) |
(Spindle 1) Automatic In-machine Tool Presetter
(Pivoting Type, without Air Blow for Presetter, Need to Clean
Manually before Measuring) (Standard) It simplifies the complicated
setup work at the tool change. The position of the tool nose is
measured pr |
| Automatic door (/2000) |
The front door is opened and closed automatically
using the air cylinder. Even when the operator is caught by the front
door, the tape switch installed in the door is immediately activated
to stop the door. Automatic door opening width: 2,560 mm (100.79 |
| Setting Unit mm |
Setting Unit, MM The unit to be used for the
screen display and program commands is set to millimeter (mm).
Turning: MM specification for the turret Horizontal machining center:
MM specification for the tapped D1252871 pallet |
| Transformer 95 kVA |
Transformer 95 kVA three phase autotransformer in
cabinet CLPB 50F-0727T08001 |
| Gear Hobbing |
Gear Hobbing This function enables to make a
program with guidance and machine spur and helical gear using hob
cutter. Regarding machining possibility including machining accuracy,
please contact DMG MORI sales staff Need to select these [ NC
option |
| Thread re-cutting |
Thread re-cutting This function allows the thread
cutting operation of a workpiece that had already previously been
removed with the thread cutting operation. |
| DXF Import function |
DXF Import function By importing 2D CAD data (DXF
data), data for workpieces with complex contours can be input easily.
Data import is possible in the GENERAL, MILLING, and HOLE processes of
the machining menu. ·Program creation time is substantially re |
| (Only for Europe) Islands, open
pockets |
Islands, open pockets Islands ·Programming
process can be greatly simplified because minimum input operation is
required even for the complex machining. Open pockets Definition of
open pockets eliminates tool paths with no machining allowance,
makin |
| Text Engraving Function |
Text Engraving Function Program for text engraving
can be output. Note: Only available for milling specification. |
| (Only for Europe) High-speed canned
cycle |
High-speed canned cycle High-speed cutting can be
specified with one line of program. This function enables the user to
reduce programming time by adding a new cycle that can create a
high-speed, time saving complicated programs. |
| MORI-APL |
MORI-APL is an application that enables a
programmer to create machining programs easily just by entering the
machining data into the items displayed sequentially on the screen.
The created programs are centrally managed. MORI-APL is fully
compatible w |
| Screen display German |
Screen display German Language on MAPPS Screen:
German Language on MAPPS Warning Screen: German Language on NC Screen:
German Language on PC Screen: German |
| Special equipment |
- Automatic centering steady rest I/F THL plus 510
(quick-change, carriage direct-coupled, dia. 85-350) - Modify
steady rest I/F (THL plus 510 > RX6Z) (quick-change, carriage
direct-coupled) - Steady rest RX6 SMW Autoblok |
| Special equipment |
Various tool holders |